Model 130NF/1314 — Single output high voltage power supply with floating ground

• Single output 0 to 30 kV
• Uses only 500 μA at max voltage
• AC input
• Ripple under 200 mV at full load
• Arc- and short-proofed
• Local/remote programming
• HV output cable included
• Floating grounding wire

Model 2591P — Single output unipolar programmable high voltage power supply

• Up to 30 kV positive or negative output
• Up to 500 μA of output current (1 mA option available)
• Extremely low output noise and ripple: under 200 mV p–p at 50 μA (low ripple with higher current available as an option)
• Differential programming input
• Separate case ground, control common, and high voltage return
• Outstanding output voltage stability (under 10 ppm/hr) and temperature coefficient (under 10 ppm/°C)
• Very good load and line regulation (0.001%)
• Outstanding slew rate (over 35 V/ms) without voltage oscillations
• Compact enclosure: 6.0 × 2.1 × 3.7 in.
• Convenient DB9 connectors for low voltage signal
• Shielded HV Caton connector
• Arc and short protected; overcurrent limited
• Commonly used for E-beam and ion beam applications

Model 2594-10 — Single output unipolar high voltage power supply

• 10 kV anode output
• Low ripple
• Low temperature coefficient
• Low stored energy
• Wide output voltage range
• Excellent stability
• Separate ground for case, signal, and power
• Common applications include ion beam generation

Model BP2592 — Single output programmable bipolar high voltage power supply

• Wide, bipolar voltage range: -30 kV to +30 kV
• Output voltage polarity reversible on the fly
• No arcing when cable unplugged from unit
• Output voltage softened by resistors
• Voltage programming via front panel mounted potentiometer
• Voltage metering via front panel digital display

Model BP2595 — Bipolar HV power supply, USB

• Wide, bipolar voltage range: -50 kV to +50 kV
• Very low ripple
• Front panel displays setpoint, status and meters
• Local control via front panel
• Remote control via USB
• Thread-safe API supports event-driven apps

Model XPS50P50 — X-ray power supply, anode + filament

• Anode voltage +2 kV to +50 kV
• Integrated anode and filament power supplies
• Programmable anode voltage and beam current
• High stability beam control
• Local and remote control modes
• Safety interlock input
• Meter outputs for beam current and HV
• Overvoltage, arc and short circuit protection

Model 550 — Single output unipolar high voltage power supply

• Single output +100 V to +5 kV
• Low-cost supply for embedded systems
• 5 kV, 40 mA output
• Line powered 120/220 VAC, 50/60 Hz
• Ground leakage detection circuit
• Remote programming
• Voltage and current monitoring outputs

Model 1316 — Single output unipolar high voltage power supply

• Single output +0.01 to +20 kV or −0.01 to −20 kV
• Very low output ripple: under 200 mV peak-to-peak at full load and 30 kV at 1 mA (20 kV at 2 mA)
• Temperature coefficient under 15 ppm/°C
• Separate connections for HV output cable shield and programming reference
• Overvoltage and overcurrent protection
• Automatic output voltage recovery after arcs and short circuits
• AC input
• Local/remote programming and metering
• Positive or negative polarity

Model 1487 — Triple output high voltage power supply

• Triple outputs (15.3 kV anode, 5.3 kV focus and 500 V grid)
• All outputs adjustable
• Low line and load regulation of high voltage outputs
• All outputs short circuit and arc protected
• Remotely programmed shutdown for each output
• All outputs current limited
• Compact size: 6 × 4 × 4 inches
• DB-9 I/O connector

Model 1617 — Triple output high voltage power supply

• Three output voltages: 20 kV anode, 5 kV focus, and 300 V grid
• Low output ripple
• Tight line and load regulation

Model 1733 — Triple output high voltage power supply

• Three outputs: 16 kV anode, −105 V G1, and 400 V G2
• 22 V to 24 V input
• Built to MIL-I-45208 standards

Model 1930 — Quad output high voltage power supply

• Four output voltages: 25 kV, 8 kV, 800 V, and −150 V
• Low output ripple
• Tight line and load regulation: under 200 mV at full load

Model 2591 — Single output high voltage power supply

• Single output +0.01 to +30 kV
• Output ripple under 200 mV p–p at 500 μA
• Temperature coefficient under 25 ppm/°C
• Stored energy under 1 J
• Low reflected ripple on input power line
• Separate connections for HV output, cable shield, and programming reference
• Compact enclosure: 6.0 × 2.1 × 3.7 in.
• Commonly used in focused ion beam systems

Model 2592 — Single output unipolar high voltage power supply

• Single output 0.01 to +50 kV or −0.01 to −50 kV
• Low ripple
• Wide output voltage range
• Low temperature coefficient
• Low stored energy
• Excellent stability
• Separate ground for case, signal, and power
• Low temperature coefficient: under 25 ppm/°C
• UL listed and CE marked at −40 kV, 100 μA
• Common applications include ion beam systems

Model 2593 — Single output high voltage power supply

• Single output 0 to +15 kV or 0 to −15 kV
• Output ripple under 200 mV peak-to-peak
• Temperature coefficient under 50 ppm/°C
• Stored energy under 0.1 J at 15 kV
• Low reflected ripple on input power line
• Compact case size
• Overvoltage and overcurrent limited
• Short-circuit and arc protected
• Automatic output voltage recovery following arcs and short circuits
• Common applications include electron beam, ion beam, and X-ray generators

Model 2594 — Single output high voltage power supply

• Single output 0 to +50 kV
• Output ripple under 300 mV p–p at full load (50 kV, 800 μA)
• Temperature coefficient under 50 ppm/°C
• Stored energy under 0.25 J at 30 kV output
• Separate connections for HV output cable shield and programming reference
• Overvoltage and overcurrent limited
• Short circuit and arc protected
• Temperature coefficient under 10 ppm/°C
• Automatic output voltage recovery after arcs and short circuits
• Floating high voltage return available
• Common applications include electron beams, ion beams, and X-ray tubes

Model 2596 — Quad unipolar output precision high voltage power supply

• Up to 30 kV positive or negative outputs
• Up to 200 μA (200–1000 μA options available upon request)
• Output noise and ripple under 200 mV p–p at full load for each output
• Independent programming, voltage, and current metering
• Output voltage stability under 10 ppm/hr
• Temperature coefficient under 10 ppm/°C
• Excellent load and line regulation (0.001%)
• Outstanding slew rate (over 35 V/ms) without voltage overshoots
• Standard 19″ rack enclosure
• Shielded high voltage CPS output connectors
• Arc and short protected, overcurrent and overvoltage limited
• AC line voltage input

Model 2600 — Single output, ultra low noise/stored energy high voltage power supply

• Single output 0 to +50 kV or 0 to −50 kV
• Only @ 500 μA at maximum voltage
• 24V to 28V DC input
• Input for remote interlock switch
• Input for remote HV enable
• Power for remote VOLTAGE ON display lamp
• Remote control via USB or RS-232 comm
• Free user interface control and display program

Model 3601 — Triple output high voltage power supply

• Accelerator output +50 to +50 kV or −50 to −50 kV
• Output ripple under 100 mV at full load
• Temperature coefficient under 300 ppm/°C
• Stored energy under 1 J
• Low reflected ripple on input power line
• Rack-mountable
• Commonly used with electron probes and similar applications

Model 3602 — Triple output high voltage power supply

• Three outputs: −30 kV 250 μA, floating −1 kV 25 μA and 5 VDC 5 A
• Compact enclosure
• Interlock input and status LEDs
• Federal Standard output connector
• RS-232 remote control
• Demo program with source code
• Ideal for electron microscopes and similar applications

Model 3603 — Triple output high voltage power supply

• Three outputs: −30 kV 330 μA, floating −1 kV 25 μA and 5 VDC 3 A
• Compact enclosure
• Interlock input and status LEDs
• Federal Standard output connector
• RS-232 remote control
• Demo software with source code
• Ideal for electron microscopes and similar applications

Model 3604 — Triple output high voltage power supply

• Accelerator output +50 to +50 kV or −50 to −50 kV
• Output ripple under 100 mV at full load
• Temperature coefficient under 300 ppm/°C
• Stored energy under 1 J
• Low reflected ripple on input power line
• Rack-mountable
• Commonly used with electron probes and similar applications

Model 5003 — Unipolar (positive or negative) high voltage power supply

• Single output 0 to +2 kV or 0 to −2 kV
• Low output ripple
• Arc and short circuit proof
• Positive or negative output
• Internal and external programming
• Output voltage metering
• DC or AC line input models
• Ideal for photomultiplier tubes

Model 250 — Precision 50 kV DC high voltage probe

• Excellent accuracy: 0.05% from 0 to 50 kV
• 1,000 MΩ input impedance
• Temperature coefficient under 50 ppm/°C
• Compact: only 12 inches in length
• Compatible with all CPS probe tips
• Measures DC voltages only

Model 500 — Precision 100 kV high voltage probe

• Excellent accuracy: 0.01% typical from 0 to 100 kV
• Handles DC input voltages to 100 kV
• 2,000 MΩ input impedance
• Temperature coefficient under 50 ppm/°C
• Compact profile; 21 inches in length
• Compatible with all CPS probe tips
• Measures DC voltages only

Model 505 — Precision USB 100 kV high voltage Probe

• Excellent accuracy: 0.01% at 10kV, 0.05% at 50 kV, 0.1% at 100 kV
• Handles DC input voltages to 100 kV
• 2,000 MΩ input impedance
• Temperature coefficient under 50 ppm/°C
• Compatible with all CPS probe tips
• Measures DC voltages only

Model 130CBL — 30 kV cable for high voltage power supplies

• Low corona noise
• Safely disconnects without arc-over
• Mates to CPS 30 kV power supplies

Model 150CBL — 50 kV cable for high voltage power supplies

• Low corona noise
• Safely disconnects without arc-over
• Mates to CPS 50 kV power supplies

Model 250CBL — 36-inch multimeter cable for CPS high voltage probes

• Adapts BNC to double banana plugs
• Compatible with all CPS analog high voltage probes
• RoHS compliant

Model USBCBL — 72-inch Cable, USB A-Mini to B

• Compatible with all CPS digital high voltage probes
• USB A-mini / B connectors

Model 3603CBL — 3-conductor high voltage cable

• Three high-voltage conductors plus outer shield
• Federal standard 3-pin connectors at both ends
• 15' overall length
• Compatible with CPS Models 3601 and 3603

Model 250B — HV probe tip, corona ball

Model 250H — HV probe tip, hook

Model 250P — HV probe tip, pointed

Model 250S — HV probe tip connector insert

Model 252CASE — Storage case for 50 kV probes

• Holds HV probe, probe tips, inserts, and manual
• Shock absorbing custom fitted molding
• Hinged handle for easy handling and compact storage
• Compatible with Model 250 and 255 probes

Model 500CASE — Storage case for 100 kV probes

• Holds HV probe, probe tips, inserts, and manual
• Shock absorbing custom fitted molding
• Hinged handle for easy handling and compact storage
• Compatible with Model 500 probe

Model HVT30 — 30 kV viewing block with AC-coupled out

• Connects HV probe to power supply and load
• AC output port for ripple monitoring
• Compatible with all CPS probes

Model USBPS — 5V USB power supply

• Wall Mount AC Adapters 5W 5V 1A USB Inlet Level VI NA wallplug

I didn't find what I need

Call us and let our knowledgeable staff help you find exactly what you need.

Need a custom solution? You've come to the right place! CPS has been designing and manufacturing custom high voltage equipment for 30+ years.